Index  >> Aquarium Products  >> Controler Series  >> CS060  
 
 
        ¡DCS020 Series
        ¡DCS060 Series
        ¡DCS062A Series
        ¡DCS063C Series
     Controler Series
 
    CS060 Series     Micom Temp Controller    
 
 
 
 
 
Features
 
1.Alarm controlled by Micom chip, yet it won't emit any sound while
   resetting the temperature or initial lower temperature.

2.It will emit a sound of alarm and cut the load of heater, if there is
   ¡Ó3¢Jerror happened between actually temperature and setting
   temperature.

3.It will emit a sound of alarm and cut the load of heater if the actually
   temperature is over 35¢J or under 20¢J.

4.when the sensor cable is cut or short-circuited, it will emit a sound of
   alarm and cut the load of heate.

5.Failure status is easy to tell by flashing symbols and emitting sounds.

6.Max Wattage load 1200W.
 
Instruction Steps
 
 
1.Connecting the the sensor cable and heater to the controller body and
   power outlet, as above picture shows.

2.Fully submerse heater and temp. sensor and mount on the tank with
   suction cups .

3.Plugging Micom controller into the power outlet.

4.Using the hook and.double sides tape to fix the controller body in a
   proper location.
 
Operation
 
1.   Initial plug in power source, the controller's LED shows the desired temperature of 29¢J, later it changes to actual water temperature after twinkling 8 times.
 
2.   With self detecting system, Micom chip when resetting the temperature or initial lower temperature, it won't emit any sound of alarm if the actual water temperature is lower the desired temperatue 3¢J. Only after the controller's red light turning off one time, It will normally emit a sound of alarm.
 
3.   the desired temperature by pressing the button , press one time to increase 1¢J¡£up to 34¢J¡¤.
 
4.   While setting the temperature, the number on controller's LED will keep twinkling and it is the desired temperature, after it twinkles 8 times the set number then return to the real water temperature.
 
5.   Controller's red light turns on¡GThe heater is heating.
 
6.   Alarm of cable disconnecting¡GThe LED shows 34¢J, and emit a sound of alarm.
 
7.   Alarm of short-circuit¡GThe LED shows and emit a sound of alarm.
 
8.   Alarm of low temperature¡GIf the actual water temperature is below 20¢J, the LED shows ,it will emit a sound of alarm and keep heating.
 
9.   Alarm of high temperature¡GIf the actual water temperature is over 35¢J, the LED shows .it will emit a sound of alarm and stop heating.
 
10.   Alarm of ¡Ó 3¢J¡GIt will emit a sound of alarm, if there is ¡Ó 3¢J error happened between actual temperature and setting temperature, when it is over +3¢J,the heater will stop heating; while it is below -3¢J, the heater will keep heating.
 
11.   Micom controller can precisely control the heating by back 0.6¢J to protect body's life.¡£if the temperature change is very tiny and lower than 0.6¢J,it won't start heating again and again.¡¤
 
12.   Correcting the desired temperature¡G press the button at same time, after the LED stop twinkling, it shows two units before and after decimal point, to adjust the number by using the screw driver ¡£flat type¡¤ to insert the correcting hole on the back of the main body.It will display the correct water temperature after 10 seconds.
 
13.   The LED returns to normal display¡Gby pressing the button at same time, after the LED stop twinkling, it returns to water temperature of two units place.
 
Important Notes
 
1.Do not stretch into the water by hand without plugging off the power outlet.

2.Do not use the damaged power cable or deformed outlet.

3.If the power outlet or plug become dirty or oxidized, they must be cleaned to
   ensure reliable operation.

4.Please check if the heater or sensor cable is out of order when any alarm is
   generated.

5.In order to detect the correct water temperature, the heater should be well
   located to get a better water circulation, and not to close to the temperature
   sensor.
 
Specification
 
Model NO. CS060
Operating temperature range 21¢J¡ã34¢J
Voltage Frequency ac110V  50¡ã60Hz
Temperature display 12¢J¡ã35¢J
Precision ¡Ó1¢J
Wattage Max load 1200W
Usage Aquarium product, control of heating water
Size
¡£mm¡¤
Body¡GWidth 70 ¡Ñ Height 154 ¡Ñ Deep 37
Power cable¡G1100
Load extension wire¡G430
Sensor cable¡G1000
Weight
¡£g¡¤
Body¡G340
¡£including power cable, sensor cable¡¤
Accessory Hanger 1pcs, double side tape 2pcs